TSMS516RK Manual.qxd 4/12/05 2:56 PM Page 1
TSMS-5/16RK
Rack-Mounted 14V/18V Satellite Multiswitch
Installation and
Operation Manual
Operation
Manual
Rev. 04/05
Ph: 800-421-6511
TSMS516RK Manual.qxd 4/12/05 2:57 PM Page 3
Safeguards
TSMS-5/16RK
11. Power Sources: This product should be operated only from the
type of power source indicated on the marking label. If you are not
sure of the type of power supplied to your home, consult your appli-
ance dealer or local power company.
12. Power-cord Protection: Power-supply cords should be routed so
they are not likely to be walked on or pinched by items placed upon or
against them. Pay particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
13. Lightning: For added protection for this product during a lightning
storm, or when it is left unattended or unused for long periods of time,
the unit should be disconnected from power source.
14. Power Lines: An outside antenna system should not be located
in the vicinity of overhead power lines, other electric light or power
circuits, where it can fall into such power lines or circuits. When
installing an outside antenna system, extreme care should be taken
to keep from touching such power lines or circuits as contact with
them may be fatal.
15. Overloading: Do not overload wall outlets and extension cords
as this can result in risk of fire or electric shock.
16. Object and Liquid Entry: Never push objects of any kind into this
product through openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
17. Servicing: Do not attempt to service this product yourself as
opening or removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service personnel.
18. Damage Requiring Service: Unplug this product from the wall
outlet and refer servicing to qualified service personnel under the
following conditions:
provide some protection against voltage surges and built-up static
charges.
a. Use No.10 AWG (5.3mm) copper, No.8 AWG (8.4mm) alu-
minum, No.7 AWG (10mm) copper-clad steel or bronze wire or
larger, as ground wire.
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
b. Secure antenna lead-in and ground wires to house with stand-
off insulators spaced from 4 feet (1.22m) to 6 feet (1.83m) apart.
d. If the product does not operate normally by following the oper-
ating instruction. Adjust only those controls that are covered by
the operating instructions. An improper adjustment may result in
damage and will often require extensive work by a qualified tech-
nician to restore the product to its normal operation.
c. Mount antenna discharge unit as close as possible to where
lead-in enters house.
d. A driven rod may be used as the grounding electrode where
other types of electrode systems do not exist. Refer to the
National Electrical Code, ANSI/NFPA 70-1984 for information.
e. If the product has been dropped or the cabinet has been
damaged.
e. Use jumper wire not smaller than No.6 AWG (13.3mm) copper
or equivalent, when a separate antenna grounding electrode is
used.
f. When the product exhibits a distinct change in performance—
this indicates a need for service.
19. Replacement Parts: When replacement parts are required, be
sure the service technician has used replacement parts specified by
the manufacturer or have the same characteristics as the original
parts. Unauthorized substitutes may result in fire, electric shock or
other hazards.
NOTE TO THE CATV SYSTEM INSTALLER
THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM
INSTALLER’S ATTENTION TO ARTICLE 820-22 OF THE NEC
THAT PROVIDES GUIDELINES FOR PROPER GROUNDING
AND, IN PARTICULAR, SPECIFIES THAT THE CABLE
GROUND SHALL BE CONNECTED TO THE GROUNDING
SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF
CABLE ENTRY AS PRACTICAL.
20. Safety Check: Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to deter-
mine that the product is in proper operating conditions.
21. Outdoor Antenna Grounding: Before attempting to install this
product, be sure the antenna or cable system is grounded so as to
3
Ph: 800-421-6511
Rev. 04/05
TSMS516RK Manual.qxd 4/12/05 2:57 PM Page 4
Descriptions
TSMS-5/16RK
Rack-Mounted 14V/18V Satellite Multiswitch
Wide frequency range:
40-2150MHz
Compatible with All DIRECTV
satellite dish reception systems
including those with incorporated
switching
Simple interface design provides 2
or 4 satellite polarity inputs and 8
or 16 outputs, for quick installation
All rear panel connection access
allows rack or wall mount flexibility
PIN diode matrix reduces polarity
transfer time and digital artifacts
providing consistent picture quality
TSMS-5/16RK
Polarity is selected by receiver
supplied voltage (14V/18VDC)
compatible with most DTH
satellite services
Rack-Mounted 14V/18V Satellite Multiswitch
Pico Macom’s TSMS-2150X Series rack-mounted satellite multiswitches can be used
in every SMATV application requiring satellite 950-2150MHz IF distribution. The easy
mount enclosure and all rear panel connections provide for rack mounting or quick
and easy wall mounting by simply turning the unit face to the wall. The TSMS-5/16RK
is compatible with DIRECTV phase three dish reception systems by allowing 4 LNB
inputs and 1 antenna and providing 16 outputs. A constant 22 kHz tone is provided
on 2 of the input ports and 14 or 18 dc volts are provided to power the LNB and
conduct internal switching. The TSMS-2150X-16A allows 2 LNB inputs and provides
16 outputs, while the TSMS-2150X-8AUV allows 2 LNB inputs and 1 off-air antenna
input and provides 8 outputs. The advanced circuit design incorporates a pin diode
matrix to route any of the inputs to any of the outputs by utilizing the 13-14V Right-
Circular/Vertical or 17-18V Left-Circular/Horizontal switching control supplied by the
satellite receivers, thus eliminating digital artifacts that result from mechanical relay
switching. To compensate for insertion loss, all versions use separate built-in amplifiers
for satellite and/or VHF/UHF signals. The TSMS-2150X series will supply power to the
LNBs reducing heat build up within the multiswitch and prolong the life of the unit.
Antenna signal combines with
satellite on output eliminating
external combining, reducing
cost and clutter
Built in DC power insertion
reduces cost by providing for LNB
power from the multiswitch
Built-in amplifier compensates for
insertion losses reducing need of
external amplification
External UL Approved power
supply reduces heat buildup thus
increasing unit life
4
Ph: 800-421-
6511
Rev. 04/05
TSMS516RK Manual.qxd 4/12/05 2:57 PM Page 5
Specifications
TSMS-5/16RK
Rack-Mounted 14V/18V Satellite Multiswitch
Front View
Rear View
Specifications
Frequency Range
Antenna In
40-2150 MHz
40-806 MHz
950-2150MHz
Input Capability
1 dB Compression
Satellite In
Antenna In
Satellite In
106 dBuV min.
108 dBuV
at 67.25 MHz Input
at 950 MHz Input
Insertion Loss
(Antenna In)
-1.5 dB max.
40-806 MHz
LHCP/RHCP
Switching Point
14.0 – 15.0 Vdc
Gain (Satellite In)
2 dB min.
0 dB min.
950-1750 MHz
1751-2150 MHz
22 KHz
Switching Point
150 – 300mVp-p
22 4 KHz
Square Wave Test Signal
Isolation
Cross Polarization
Out to Out
-25 dB min.
-14 dB min.
-28 dB min.
-35 dB min.
950-2150 MHz
40-806 MHz
950-2150 MHz
950-2150 MHz
Output 22KHz Signal
Characteristic
Frequency Amplitude
Sat In to Sat In
650 250 mV p-p
75 ohms All Ports
Stop Band Attenuation
15 dB min.
15 dB min.
Ant port @ 950 MHz
Sat port @ 806 MHz
Impedance
Power Input
Dimensions
Weight
120 Vac 10%, 60 Hz, 140 mA
19˝(L) x 5.5˝(D) x 1.75˝(H)
4.8 lbs.
Return Loss
Input / Output
-5 dB min.
-8 dB min.
-6 dB min.
40-806 MHz
950-1450 MHz
1451-2150 MHz
Ordering Information
TSMS-5/16RK
DIRECTV Phase 3 ODU Compatible 5 Input 16 Output
5
Ph: 800-421-6511
Rev. 04/05
TSMS516RK Manual.qxd 4/12/05 2:57 PM Page 6
Operation and Controls
TSMS-5/16RK
Front Panel
Back Panel Control
1. 18V 22KHz:
Connect the 18Vdc 22 KHz output of a LNB to this port.
5. ANT IN:
Connect the cable from a off-air antenna to this port.
2. 14V 22KHz:
Connect the 14Vdc 22 KHz output of a LNB to this port.
6. OUT:
Connect a satellite receiver to this port. If an off-air antenna
is employed, insert a TSDM-2150 diplexer between the OUT
port and the receiver input.
3. 18V 0KHz:
Connect the 18Vdc 0KHz output of a LNB to this port.
7. Power Cord:
4. 14V 0KHz:
Connect the 14Vdc 0KHz output of a LNB to this port.
Insert the power cord into a 3 prong 120Vac 60Hz
receptacle only.
6
Ph: 800-421-6511
Rev. 04/05
TSMS516RK Manual.qxd 4/12/05 2:58 PM Page 7
Installation Procedure
TSMS-5/16RK
Installation
It is recommended that assistance be available to safely install equipment in equipment racks.
1. Install chassis in equipment rack (equipment rack sold separately) by supporting the bottom and rear of TSMS-5/16RK at the
desired elevation in rack.
2. Line up the side holes of chassis with the tapped equipment rack holes.
3. Insert the provided screws through the mounting holes at the extreme left and right of faceplate and thread into the tapped
equipment rack holes.
4. Fasten the bottom screws first, then fasten top screws (tighten securely).
5. Connect a cable from the RHCP port of a LNB to the LNB RHCP (14V) port of the TSMS-5/16RK.
6. Connect a cable from the LHCP port of a LNB to the LNB LHCP (18V) port of the TSMS-5/16RK.
7. Connect a cable from the RHCP port of a LNB to the LNB RHCP (14V, 22KHz) port of the TSMS-5/16RK.
8. Connect a cable from the LHCP port of a LNB to the LNB LHCP (18V, 22KHz) port of the TSMS-5/16RK.
9. If employing an off-air antenna, connect the antenna cable to the ANT IN port of the TSMS-5/16RK.
10. Connect a receiver input directly to the OUT port of the unit if not using an off-air antenna.
11. If using an off-air antenna connect the ANT/SAT of a TSDM-2150 diplexer to the OUT port of the switch. Connect a satellite
receiver SAT IN to the SAT port and the satellite receiver ANT IN to the ANT. Port of the TSDM-2150.
12. Plug the power cord into a 120Vac 60Hz wall receptacle.
7
Ph: 800-421-6511
Rev. 04/05
TSMS516RK Manual.qxd 4/12/05 2:58 PM Page 8
Warranty
TSMS-5/16RK
Limited Warranty
Pico Macom warrants to the original purchaser that all of its new products are of sound design, quality materials and workmanship at the time of manufacture
and will be free from related defects for one year from the original purchase date. Pico Macom will repair or, at its discretion, replace without cost to the original
purchaser, the product which, upon inspection by Pico Macom, appears to be defective or not conforming to factory specifications. Pico Macom will cover the cost
of parts, labor, and return freight from factory.
Five-Year Limited Warranty
Most products designated as “Headend Electronics” are further covered by an extended 4-year period beyond the expiration of the original 1-year warranty, for a
full 5-year period. Qualified equipment requiring factory repair during the extended 4-year period is covered under our re-certification program. Re-certification fees
under this program shall not to exceed 20% of the product’s List Price and whenever possible, Pico Macom will attempt to upgrade performance to the latest
improved specification.
Warranty Limitations
This warranty excludes coverage of damage or inoperability resulting from (1) use or installation other than in strict accordance with Pico Macom’s written instruc-
tions, (2) disassembly or repair by someone other than Pico Macom or a Pico Macom authorized repair center, (3) misuse, misapplication or abuse, (4) alteration,
(5) lack of reasonable care or (6) wind, ice, snow, rain, lightning, power surges, or any other weather conditions or acts of God. Pico Macom’s warranty with respect
to third-party proprietary sub-assembly modules and/or private-label products are limited to the duration and terms of third-party vendors’ warranty. Pico Macom
shall in no event and under no circumstances be liable or responsible for any consequential, indirect, incidental, punitive, direct or special damages based upon
breach of warranty, breach of contract, negligence, strict tort liability or otherwise or any other legal theory, arising directly or indirectly from the sale, use, installa-
tion or failure of any product acquired by buyer from Pico Macom. This limited warranty extends to the original purchaser. Pico Macom reserves the right to modify
or discontinue this warranty at Pico Macom’s sole discretion without notification. No other warrantees are expressed or implied.
Uptime Loaner Program
Our Uptime loaner program is designed to provide domestic users of our headend products and commercial systems the best possible support and service. This
program is established to minimize downtime resulting from equipment failure in critical service situations. We offer this program free-of-charge (excluding freight)
to qualified purchasers within the warranty period. The program provides a free equipment loan of like qualified equipment enabling seamless operation for the time
required to repair and return the unit.
The process is simple. Call our Customer Service desk requesting a return-merchandise-authorization (RMA) number for the failed equipment and ask for a loan-
er unit. We will issue an invoice for the List Price of the loaner unit plus shipping costs. When you receive the loaner unit, pack the failed unit in the loaner unit’s
box and ship it freight prepaid to Pico Macom for repair. When you receive the repaired unit, a new RMA number will be provided in the box. Carefully pack the
loaner unit and affix the new RMA number on the box and ship it back to us for full credit excluding shipping costs.
To qualify for the program, you must have current open-terms with us and in good standing. We must receive your failed unit within one week after the loaner unit
is shipped to you, and must likewise receive the loaner unit within one week after the repaired unit is shipped back to you. Daily rental fees not to exceed 10% of
the equipment’s List Price will apply beyond one week after the loaner or repaired unit are shipped to you. Other limitations may apply, so please call us for addi-
tional information on qualifying equipment and procedures. Pico Macom reserves the right to modify or discontinue the Uptime Loaner Program at any time, and at
its sole discretion.
Damage or Shortage Claims
Our shipping staff carefully packs and ships your orders in compliance with common carriers’ requirements. Please make note of any obvious damage or shortage
on the freight bill or carrier’s receipt next to your signature. The carrier’s agent must too sign acknowledging the loss. Failure to do so may result in the carrier’s
refusal to honor the claim. Please open your order immediately upon receipt to check for concealed damage and compare the packing list to the items shipped. If
damaged, keep the original shipping cartons for possible inspection by the carrier. You must report claims for loss or damage within 3 days of delivery, while claims
for erroneous charges or price corrections must be presented within 30 days of invoice date.
Returning Shipped Items
To return any shipped items, including those shipped for warranty repairs or credit, call our Customer Service desk to request a Return Merchandise Authorization
(RMA) number. Please reference the original invoice number and purchase date, and product serial number (if any). Be certain to mark the RMA number on the
package boldly and legibly. Unless we specify a different carrier, please ship your returned items to us via UPS freight prepaid and fully insured. If returned for
credit, we will promptly process your request upon receipt of your return order.
Our Return Policy: Your Satisfaction Guaranteed
Our goal is your complete satisfaction. If for any reason, our products were not quite what you anticipated, simply call your customer service rep and
we will be happy to assist you in replacing or returning the order. You may return current, non-discontinued items for full credit for up to 30 days from
invoice date. Our requirements are simple: Excepting defective items, the products must be returned in their original packaging and in re-salable
condition. Restocking fees may otherwise apply beyond this period or if products are not returned in their original condition. Please contact your
customer service rep for more information.
8
Ph: 800-421-6511
Rev. 04/05
|